Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PULL_PIN_DEFAULT is meant for hardware completely hiding any pull
settings from the driver, so that it's really only possible to turn
the pull on or off, but it not being possible to determine any
pull settings from software.
Also the binding-documentation for the pull arguments did not match
the changes to the expected values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds new regulator driver to support max77693 chip's regulators.
max77693 has two linear voltage regulators and one current regulator which
can be controlled through I2C bus. This driver also supports device tree.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 12 pins that can be configured depending on the system
configuration. Allow settting the corresponding registers from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Interlaken is a narrow, high speed channelized chip-to-chip interface. To
facilitate interoperability between a data path device and a look-aside
co-processor, the Interlaken Look-Aside protocol is defined for short
transaction-related transfers. Although based on the Interlaken protocol,
Interlaken Look-Aside is not directly compatible with Interlaken and can be
considered a different operation mode.
The Interlaken LA controller connects internal platform to Interlaken serial
interface. It accepts LA command through software portals, which are system
memory mapped 4KB spaces. The LA commands are then translated into the
Interlaken control words and data words, which are sent on TX side to TCAM
through SerDes lanes.
Signed-off-by: Joe Liccese <joe.liccese@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.
These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).
The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Sekhar Nori:
DaVinci SoC updates for v3.11 - part 2
This pull request adds DT and runtime PM to
EDMA ARM private API so it can be used on
DT enabled DaVinci and OMAP platforms.
Also adds DMA channel crossbar mapping
support to be used by DT-enabled platforms
which use it.
* tag 'davinci-for-v3.11/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
ARM: edma: Convert to devm_* api
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds primitive DT support to the max8973 regulator driver. None
of the configuration parameters, supported in the platform data are yet
available in DT, therefore no configuration is performed if booting with
no platform data. This means, that DT instantiation can only be used on
boards, where no run-time configuration of the chip is required. In such
cases the driver can be used to scale its output voltage. In the future
support for configuration parameters should be added.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same way to define pin muxing and pin configuration
than for nomadik. So pickup code from pinctrl_nomadik.c to be
able to implement pin multiplexing and pin configuration using
the device tree. Pin configuration uses generic parsing code.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The binding definition is based on the generic DMA controller
binding.
Joel:
* Droped reserved and queue DT entries from Documentation
for now from the original patch series (v10)
* Included properties in Documentation and clarified DMA properties (V11)
* Made ti,hwmod option
* Clarified DMA entries
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds device trees for describing the TI-Nspire hardware.
Changes between v1 and v2:
* Change "keymap" binding to the standard "linux,keymap" binding.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Christian Daudt:
* 'armsoc/for-3.11/dt' of git://github.com/broadcom/bcm11351:
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: dts: bcm281xx: use existing defines for irqs
ARM: dts: bcm281xx: use #include for device tree files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Second Round of Renesas ARM-based SoC DT updates for v3.11
* Increased DT coverage for renesas-intc-irqpin
by Guennadi Liakhovetski
* Clean up of address format used in sh73a0 dtsi file
by Guennadi Liakhovetski
* tag 'renesas-dt2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: shmobile: sh73a0: remove "0x" prefix from DT node names
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Second Round of Renesas ARM based SoC GPIO R-Car updates for v3.11
Documentation enhancement and code cleanup by Laurent Pinchart.
* tag 'renesas-gpio-rcar2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim:
based on tags/common-clk-audio
- add support for exynos5420 SoC
* tag 'soc-exynos5420-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: extend soft-reset support for EXYNOS5420
ARM: EXYNOS: add secondary CPU boot base location for EXYNOS5420
clocksource: exynos_mct: use (request/free)_irq calls for local timer registration
ARM: dts: Add initial device tree support for EXYNOS5420
clk: exynos5420: register clocks using common clock framework
ARM: EXYNOS: use four additional chipid bits to identify EXYNOS family
serial: samsung: select EXYNOS specific driver data if ARCH_EXYNOS is defined
ARM: EXYNOS: Add support for EXYNOS5420 SoC
ARM: dts: list the CPU nodes for EXYNOS5250
ARM: dts: fork out common EXYNOS5 nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Heiko Stuebner:
Adds basic support for Rockchip Cortex-A9 SoCs.
* tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
clocksource: dw_apb_timer_of: use clocksource_of_init
clocksource: dw_apb_timer_of: select DW_APB_TIMER
clocksource: dw_apb_timer_of: add clock-handling
clocksource: dw_apb_timer_of: enable the use the clocksource as sched clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The LP55xx DT structure is applicable to the LP5562 device.
The driver and documentation are updated.
Compatible property of the DT
: LP5521 and LP5223 were manufactured by National Semiconductor.
LP5562 is a new device from Texas Instruments.
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Currently, the LP55xx DT structure supports max 3 channels.
However, LP5523 has max 9 channels and LP5562 has 4 channels.
To enhance this constraint, the DT structure has been changed.
(a) Use the child node for various channel settings instead of fixed array
(b) Remove 'num_channel' property.
This value can be retrieved by counting the children node.
(c) 'chan-name' property supported
(d) Documentation updates for LP5521 and LP5523
(cooloney@gmail.com: fix a coding style issue in leds-lp55xx.txt)
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch allows the lp5521 driver to be successfully probed and
initialised when Device Tree support is enabled.
Based on a patch by Gabriel Fernandez, rewritten in accordance
with review feedback.
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds basic support for gate-clocks on Rockchip SoCs.
There are 16 gates in each register and use the HIWORD_MASK
mechanism for changing gate settings.
The gate registers form a continuos block which makes the dt node
structure a matter of taste, as either all 160 gates can be put into
one gate clock spanning all registers or they can be divided into
the 10 individual gates containing 16 clocks each.
The code supports both approaches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add SDHCI bindings for the Broadcom 281xx SoCs.
Changes from V2:
- Documentation cleanups
Changes from V1:
- split original patch into 2, one for driver and this one for dt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim:
based on exynos-dt-2 and s3c24xx-dt-2
- use #include for all Samsung DT
- add clk for exynos audio subsystem (audss) and i2s
- support audss and i2s for exynos5250
* tag 'common-clk-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim:
2nd exynos dt update based on tags/exynos-dt-1
- enable RTC on exynos5250 snow and Arndale boards
- add support LCD and PWM for exynos4210 Origen board
- update bootargs to support 8GiB for exynos5440 SSDK5440 and SD5v1 boards
- enable spi and add opp level for exynos5440
- add example doc for samsung-pinctrl dt bindings
* tag 'exynos-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Set BUCK7 as always on for Origen board
ARM: dts: Add FIMD node to Origen4210 board
ARM: dts: Add LCD related pinctrl entries for exynos4210
ARM: dts: Add PWM related pinctrl entries for exynos4210
Documentation: Add examples to samsung-pinctrl device tree bindings documentation
ARM: dts: Enable RTC node for exynos5250-snow
ARM: dts: Enable RTC node for Arndale
ARM: dts: Removing pdma for exynos5440
ARM: dts: update bootargs to support 8GiB for SSDK5440 and SD5v1
ARM: dts: Add more opp levels in exynos5440
ARM: dts: Add wm8994 regulator support on smdk5250
ARM: dts: enable spi for EXYNOS5440 SOC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren:
PM voltage domain clean-up via Kevin Hilman <khilman@linaro.org>:
OMAP: PM: remove requirement for voltage domain data; remove dummy data
* tag 'omap-for-v3.11/pm-voltdomain-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33xx: Remove the unused voltagedomain data
ARM: OMAP2+: Powerdomain: Remove the need to always have a voltdm associated to a pwrdm
Includes an update to Linux 3.10-rc6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Linus Walleij:
Nomadik DT and clock work:
- Lee Jones' pinctrl compat ontology patches
- A real clock driver for the Nomadik, 100% DT-based
- Device tree changes for the Nomadik clocks
* tag 'nomadik-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
pinctrl/nomadik: Standardise Pinctrl compat string for Nomadik based platforms
ARM: nomadik: Standardise Nomadik STN8815 based Pinctrl compat string in the DTS
Conflicts:
arch/arm/boot/dts/ste-nomadik-s8815.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Maxime Ripard:
Allwinner platform additions, take 2
Adds machine support for the Allwinner A10s SoC
* tag 'sunxi-core-for-3.11-2' of git://github.com/mripard/linux:
ARM: sunxi: Add Allwinner A10s machine compatible
Depends on the sunxi/cleanup branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added a property to indicate if the regulator supports bypass mode.
Also modified of_get_regulation_constraints() to check for that
property and set appropriate constraints.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TWL6025 was never released beyond sample form and was replaced by
the PhoenixLite range of chips - TWL6032. Change the references to
reference the TWL6032 class and name the registers to twl6032 in line with
an actual released chip name to avoid confusion.
Currently there are no users of TWL6025 in the code.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviwed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
The Nomadik clock implementation was a stub just using
fixed clocks.
This implements the clocks properly instead of relying
on them all being on at boot and leaving them all on.
The PLLs are on the top locking to the main chrystal
oscillator, then the HCLK for the peripherals are
below PLL2.
The gated clocks are implemented with zero cells and
given the clock ID as a property of each node, so every
gate need to have its own node in the device tree.
This is because the gate registers contain both HCLK
gates and PCLK gates, where the latter has HCLK as
parent. As can be seen from the register layout, this
is a complete mixup, which means all these gates need
their own node to properly model parent/child relations
for PCLKs apart from the HCLKs.
This driver also adds a helpful debugfs file to inspect
the hardware state of the clock gates.
This is the end result in <debugfs>/clk/clk_summary
after applying a proper device tree:
ulpiclk 0 0 60000000
mxtal 3 3 19200000
pll2 1 1 864000000
clk48 3 3 48000000
rngcclk 1 1 48000000
usbmclk 0 0 48000000
mshcclk 0 0 48000000
mspclk3 0 0 48000000
x3dclk 0 0 48000000
skeclk 0 0 48000000
owmclk 0 0 48000000
mspclk2 0 0 48000000
mspclk1 0 0 48000000
uart2clk 0 0 48000000
ipbmcclk 0 0 48000000
ipi2cclk 0 0 48000000
usbclk 0 0 48000000
mspclk0 0 0 48000000
uart1clk 1 2 48000000
i2c1clk 0 0 48000000
i2c0clk 0 0 48000000
sdiclk 1 1 48000000
uart0clk 0 0 48000000
sspiclk 0 0 48000000
irdaclk 0 0 48000000
clk72 0 0 72000000
difclk 0 0 72000000
clcdclk 0 0 72000000
clk216 0 0 216000000
hsiclkrx 0 0 216000000
clk108 0 0 108000000
hsiclktx 0 0 108000000
clk27 0 0 27000000
pll1 1 1 264000000
hclk 3 3 264000000
hclkrng 1 1 264000000
hclkusbm 0 0 264000000
hclkcryp 0 0 264000000
hclkhash 0 0 264000000
hclk3d 0 0 264000000
hclkhpi 0 0 264000000
hclksva 0 0 264000000
hclksaa 0 0 264000000
hclkdif 0 0 264000000
hclkusb 0 0 264000000
hclkclcd 0 0 264000000
hclkdma1 0 0 264000000
hclksdram 0 0 264000000
hclksmc 1 1 264000000
hclkdma0 0 0 264000000
pclk 7 9 264000000
pclkmsp3 0 0 264000000
pclkmshc 0 0 264000000
pclkhsem 0 0 264000000
pclkske 0 0 264000000
pclkowm 0 0 264000000
pclkmsp2 0 0 264000000
pclkmsp1 0 0 264000000
pclkuart2 0 0 264000000
pclkxti 0 0 264000000
pclkhsi 0 0 264000000
pclkmsp0 0 0 264000000
pclkuart1 1 1 264000000
pclki2c1 0 0 264000000
pclki2c0 0 0 264000000
pclksdi 1 1 264000000
pclkuart0 1 1 264000000
pclkssp 0 0 264000000
pclkirda 0 0 264000000
timclk 1 1 2400000
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo:
imx device tree changes for 3.11:
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
* tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (82 commits)
ARM: dts: imx27: Add VPU devicetree node
ARM: mxc: fix gpio-ranges for VF610
ARM: dtsi: imx6qdl-sabresd: Enable WM8962 audio support
ARM: dtsi: imx6qdl-sabresd: Enable SSI2 and AUDMUX
ARM: dtsi: imx6qdl-sabresd: Add WM8962 CODEC support
ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962
ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX
ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1
ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration
ARM: dts: Phytec imx6q pfla02 and pbab01 support
ARM: dts: imx6q: Add pinctrl for usdhc2 and enet
ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash
ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support
ARM: dts: i.MX27: Add SDHC devicetree nodes
ARM: dts: i.MX27: Add DMA devicetree node
ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR
ARM: dts: imx6dl: add pinctrls for WEIM NOR
ARM: dts: imx6q: add pinctrls for WEIM NOR
ARM: dts: imx6qdl: add more information for WEIM
ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Linus Walleij:
This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: basic PCIv3 device tree support
ARM: integrator: move static ioremapping into PCIv3 driver
ARM: integrator: move VGA base assignment
ARM: integrator: remap PCIv3 base dynamically
ARM: integrator: move V3 register definitions into driver
ARM: integrator: move PCI base address grab to probe
ARM: integrator: grab PCI error IRQ in probe()
ARM: integrator: convert PCIv3 bridge to platform device
ARM: integrator: merge PCIv3 driver into one file
ARM: pci: create pci_common_init_dev()
Documentation/devicetree: add a small note on PCI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
