spi: quad: fix the name of DT property in patch
The previous property name spi-tx-nbits and spi-rx-nbits looks not
human-readable. To make it consistent with other devices, using property
name spi-tx-bus-width and spi-rx-bus-width instead of the previous one
specify the number of data wires that spi controller will work in.
Add the specification in spi-bus.txt.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the probe routine to get the port line number
from device tree if the 'of_node' is populated in the
platform device. The driver can be built as module,
thus add an OF specific module device table as well
to support module auto loading.
This makes it possible to use the driver for AR9330
UART devices specified in device tree.
Cc: devicetree@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device tree property should be more descriptive.
microchip seems more reasonable than mcp. The old mcp
prefix is still supported but marked as deprecated.
Users of mcp have to switch to the microchip prefix.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dout_pixel is a new ID allocated for pixel clock divider. It is
queried in the driver to pass as the parent to hdmi clock while
switching between parents.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
hdmi driver needs to change the parent of hdmi clock
to pixel clock or hdmiphy clock, based on the stability
of hdmiphy. This patch is exposing the mux for changing
the parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add sclk_hdmiphy to the list of exposed clocks. This is required
by hdmi driver to change the parent of hdmi clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
Let's fix up the msm serial device bindings so that it's clearer
what hardware is supported. Instead of using hsuart (for high
speed uart) let's use uartdm because that matches the actual name
of the hardware. Also, let's add the version information in case
we need to differentiate between different versions of the
hardware in the future. Finally, lets specify that clocks are
required (the clock bindings didn't exist when the original
binding was written) and also specify dma bindings just in case
we want to use it in software. We split the binding into two
files to make it clearer what's required and not required.
Cc: David Brown <davidb@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all bindings in bindings/tty/serial into bindings/serial so we only
have one place dir with serial/uart related bindings in it.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had two bindings for the same serial device, it looks like the one in
tty/serial/fsl-imx-uart.txt is the more up to date one so go with it and
merge a few things about the use/need for aliases in from
serial/fsl-imx-uart.txt.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support for both am335x-USB instances required changes to the device
tree bindings. This patch reflects these changes in the bindings
document.
v3…v4:
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
v2…v3:
- use proper usb-phy nodes in evm, bone and evmsk device tree.
v1…v2:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- use usbX-phy instead of usbX_phy
- use dma-controller instead of dma
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This facilitates DMAC DT support by eliminating the need in AUXDATA and
avoiding creating complex DT data. This also fits well with DMAC devices,
of which SoCs often have multiple identical copies and it is perfectly
valid to use a single configuration data set for all of them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds device tree support for contiguous and reserved memory
regions defined in device tree.
Large memory blocks can be reliably reserved only during early boot.
This must happen before the whole memory management subsystem is
initialized, because we need to ensure that the given contiguous blocks
are not yet allocated by kernel. Also it must happen before kernel
mappings for the whole low memory are created, to ensure that there will
be no mappings (for reserved blocks) or mapping with special properties
can be created (for CMA blocks). This all happens before device tree
structures are unflattened, so we need to get reserved memory layout
directly from fdt.
Later, those reserved memory regions are assigned to devices on each
device structure initialization.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
The driver now supports the chips pca9633 and pca9634, therefore we
rename the files to more generic and meaningul names
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add support for PCA9634 chip, which belongs to the same family as the
9633 but with support for 8 outputs instead of 4.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add hardware blinking support to the pca9633 driver.
NOTE: Hardware blinking violates the leds infrastructure
driver interface since the hardware only supports
blinking all LEDs with the same delay_on/delay_off
rates. That is, only the LEDs that are set to blink
will actually blink but all LEDs that are set to blink
will blink in identical fashion. The delay_on/delay_off
values of the last LED that is set to blink will be used
for all of the blinking LEDs. If the hardware doesn't
support the requested blinking pattern, a default of
500ms on and off will be used.
Hardware blinking is disabled by default but can be enabled
by setting the 'blink_type' member in the platform_data
struct to 'PCA9633_HW_BLINK' or by adding the 'nxp,hw-blink'
property to the DTS.
(fengguang.wu@intel.com: Removes unneeded semicolon.)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP8501 can drive up to 9 channels like LP5523.
LEDs can be controlled directly via the I2C and programmable engines are
supported.
LP55xx common driver
LP8501 is one of LP55xx family device, so LP55xx common code are used.
Chip specific data is defined in the structure, 'lp55xx_device_config'.
Differences between LP8501 and LP5523
Different register layout for LED output control and others.
LP8501 specific feature for separate output power selection.
LP8501 doesn't support external clock detection.
Different programming engine data.
LP8501 specific feature - output power selection
Output channels are selected by power selection - Vout or Vdd.
Separate power for VDD1-6 and VDD7-9 are available.
It is configurable in the platform data.
To support this feature, LP55xx DT structure and header are changed.
Device tree binding is updated as well.
LED pattern data
Example pattern data is updated in the driver documentation.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Similar to tca6507, we can just parse the standard LED
properties for pca9633.
Tested on a pca9632, which is compatible with pca9633.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the ROM script addresses for i.MX25, i.MX5x and i.MX6 to the
SDMA driver needed for the driver to work without additional firmware.
The ROM script addresses are SoC specific and in some cases even tapeout
specific. This patch adds the ROM script addresses only for SoCs which
do not have a tapeout specific SDMA ROM, because currently it's unclear
how this case should be handled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Allwinner A20 is almost identical to the earlier A10 SoC from
Allwinner on many aspects, including the clocks tree. However, since the
A20 has some additionnal IPs compared to the A10, the clock tree isn't
exactly the same, especially when it comes to the gated clocks
available. We thus need to register different clock gates for the A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The A31 has a mostly different clock set compared to the other older
SoCs currently supported in the Allwinner clock driver.
Add support for the basic useful clocks. The other ones will come in
eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
From Shawn Guo:
It contains the imx device tree updates for 3.12.
- New pinctrl entry additions for various peripherals
- Devices enabling for imx6, imx5 and imx27 boards
- Add missing device nodes like iim, owire, audmux and sram, etc.
- Various updates on boards like phytec, wandboard and sabresd
- Consolidate pad macros between imx6q and imx6dl
* tag 'imx-dt-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6: (92 commits)
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
ARM: dts: i.MX27: Increase "clock-latency" value
ARM: dts: i.MX27: Add label to CPU node
ARM: dts: i.MX27: Remove optional "ptp" clock source for FEC
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Shawn Guo:
It contains a bunch of imx soc updates for 3.12.
- Add more ethernet phy fixups for imx6 boards
- Add some missing imx6q clocks into clock driver
- Add new clock types fixup mux and div to work around some ugly
hardware defect
- Consolidate L2 cache initialization function, so that it can be used
on more i.MX SoCs
- Replace magic numbers in mach-imx6q.c with well defined macros
- Small fixes for imx6q and pllv3 clock drivers
- Some random updates on imx defconfig files
* tag 'imx-soc-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6: (33 commits)
phy: micrel: Add definitions for common Micrel PHY registers
ARM: imx: Re-select CONFIG_SND_SOC_IMX_MC13783 option
ARM: imx: Move anatop related from board file to anatop driver
ARM: imx_v6_v7_defconfig: Enable wireless support
ARM: imx_v4_v5_defconfig: Cleanup imx_v4_v5_defconfig
ARM: imx_v6_v7_defconfig: Add SATA support
ARM: imx_v6_v7_defconfig: Cleanup imx_v6_v7_defconfig
ARM: mx53: Allow suspend/resume
ARM: mach-imx: Select ARM_CPU_SUSPEND at ARCH_MXC level
ARM: imx_v6_v7_defconfig: Select CONFIG_TOUCHSCREEN_EGALAX
ARM: imx6q: add vdoa gate clock
ARM: imx6q: add the missing cko output selection
ARM: imx6q: add cko2 clocks
ARM: imx6q: add spdif gate clock
ARM: imx: clk-pllv3: improve the timeout waiting method
ARM: imx6: change some clocks to fixup clocks
ARM: imx: add common clock support for fixup mux
ARM: imx: add common clock support for fixup div
ARM: imx: Select MIGHT_HAVE_CACHE_L2X0
ARM: imx: fix imx_init_l2cache storage class
...
From Shawn Guo:
This is a patch series that updates imx-weim bus driver to have it
support more i.MX SoCs. Because there is no maintainer for
drivers/bus so far, I'm forwarding it through IMX tree for 3.12 merge
window.
* tag 'imx-weim-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6:
drivers: bus: imx-weim: Add support for i.MX1/21/25/27/31/35/50/51/53
drivers: bus: imx-weim: Add missing platform_driver.owner field
drivers: bus: imx-weim: use module_platform_driver_probe()
drivers: bus: imx-weim: Simplify error path
drivers: bus: imx-weim: Remove private driver data
use exact SoC revision instead of wildcard describing
the compatible property requirement in the binding
document. This will make the binding more clearer.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C Transaction Generator offloads CPU from managing I2C
transfer step by step.
This feature is currently only available on Armada XP, so usage of
this mechanism is activated through device tree.
Based on the work of Piotr Ziecik and rewrote to use the new way of
handling multiples i2c messages.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
