From Tony Lindgren:
Few device tree changes that fix boot time warnings and
make panda display work with recent u-boot.
* tag 'omap-for-v3.13/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the AM33xx RNG module's device tree data.
Also add Documentation file describing the data
for the RNG module.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The standard interrupts property in device tree can only handle
interrupts coming from a single interrupt parent. If a device is wired
to multiple interrupt controllers, then it needs to be attached to a
node with an interrupt-map property to demux the interrupt specifiers
which is confusing. It would be a lot easier if there was a form of the
interrupts property that allows for a separate interrupt phandle for
each interrupt specifier.
This patch does exactly that by creating a new interrupts-extended
property which reuses the phandle+arguments pattern used by GPIOs and
other core bindings.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
[grant.likely: removed versatile platform hunks into separate patch]
Cc: Rob Herring <rob.herring@calxeda.com>
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper, mvebu dt changes for v3.13 (round 4):
- mvebu
- core divider clock driver dt binding and nodes
* tag 'dt-3.13-4' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add the core-divider clock to Armada 370/XP
ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
ARM: mvebu: Add Core Divider clock device-tree binding
From Shawn Guo:
The imx/mxs device tree changes for 3.13:
- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree
* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
ARM: dts: imx6sl-evk: enable the SPI NOR
ARM: dts: imx6sl: add a pinctrl for ECSPI1
ARM: imx27: add missing #pwm-cells property
ARM: dts: imx6sl: add pinctrl uhs states for usdhc
ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
ARM: imx27-apf27dev: Add framebuffer support
ARM: imx51-apf51dev: Add parallel display support
ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
ARM: dts: mxs: Add MSR M28CU3 board
ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
ARM: dts: imx6qdl: add pcie device node
ARM: dts: imx6q-udoo: Add initial board support
ARM: dts: mxs: Add muxing options for the SSP2 MMC
ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Shawn Guo:
The imx/mxs soc changes for 3.13:
* Low-level debug support for Vybrid
* Support soc bus/device for imx6
* Suspend support for imx6dl and imx6sl
* The imx6q clock updates for PCIe and audio PLL support
* IOMUXC GPR update for fec support
* Some random cleanup
* A few defconfig updates
* tag 'imx-soc-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (31 commits)
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
ARM: mach-imx: clk-imx51-imx53: Retrieve base address and irq from dt
ARM: mxs_defconfig: Add CHIPIDEA_UDC support
ARM: imx: Include linux/err.h
ARM: imx_v6_v7_defconfig: Add CHIPIDEA_UDC support
ARM: imx_v6_v7_defconfig: Add SPDIF support
ARM: imx6q: clock and Kconfig update for PCIe support
ARM: imx: Add LVDS general-purpose clocks to i.MX6Q
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Allwinner sunXi SoCs machine additions for 3.13
Nothing outstanding here, mostly some documentation cleanup, and the split of
the previous generic machine declaration into three different machines to
handle the sun4i/sun5i, sun6i and sun7i separately.
* tag 'sunxi-core-for-3.13' of https://github.com/mripard/linux:
Documentation: dt: Remove clock gates IDs list for Allwinner SoCs
Documentation: dt: Remove interrupt sources list for Allwinner SoCs
Documentation: sunxi: Update Allwinner SoC documentation
Documentation: sunxi: Update A13 user manual dead link
ARM: sunxi: Order Kconfig options alphabetically
ARM: sunxi: Simplify restart setup code
ARM: sunxi: Split out the DT machines for sun6i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim, these are device-tree updates for Exynos. Among the changes:
- add MIPI PHY node for exynos4
- update regulator for origen and exynos5250-arndale
- add support HDMI for exynos5250, exynos5420
* commit '93457b9cb980ffeeef020c3bcd99065c3807619b':
ARM: dts: Add HDMI related I2C nodes for Arndale board
ARM: dts: enable hdmi subsystem for exynos5420 smdk board
ARM: dts: add dt nodes for hdmi subsystem for exynos5420
ARM: dts: add i2c device nodes for Exynos5420
ARM: dts: add clocks to hdmi dt node for exynos5250
ARM: dts: add mixer clocks to mixer node for Exynos5250
of/documentation: update with clock information for exynos hdmi subsystem
ARM: dts: Disable Exynos5250 I2S controllers by default
ARM: dts: Add reg property to regulator nodes in exynos5250-arndale
ARM: dts: Add fixed voltage regulator to simple bus for origen
ARM: dts: Add MIPI PHY node to exynos4.dtsi
From Kukjin Kim, this branch adds device-tree support to the DMA controller
on the older Samsung SoCs. It also adds support for one of the missing SoCs
in the family (2410).
The driver has been Ack:ed by Vinod Koul, but is merged through here due
to dependencies with platform code.
* tag 's3c24xx-dma' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
+ Linux 3.12-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds support for the bq24735 charger chipset. The bq24735 is a
high-efficiency, synchronous battery charger.
It allows control of the charging current, input current, and the charger
voltage DAC's through SMBus.
Signed-off-by: Darbha Sriharsha <dsriharsha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Thanks-to: Stephen Warren <swarren@wwwdotorg.org>
Thanks-to: Thierry Reding <thierry.reding@gmail.com>
Thanks-to: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves the handling of the chip's enable pin from the board
code into the driver. It also updates all board-code files using the
driver to incorporate this change.
This is needed for device tree support of the enable pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support to tpa6130a2 driver and document the
bindings.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Device tree support for Davinci Machine driver
When the board boots with device tree, the driver will receive card,
codec, dai interface details (like the card name, DAPM routing map,
phandle for the audio components described in the dts file, codec mclk
speed). The card will be set up based on this information. Since the
routing is provided via DT we can mark the card fully routed so core
can take care of disconnecting the unused pins.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove last reference to num-serializer in davinci-mcasp devicetree
binding document.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ams AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
controller, 11 LDOs, RTC, automatic battery, temperature and
over-current monitoring, 8 GPIOs, ADC and a watchdog.
Add MFD core driver for the AS3722 to support core functionality.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The serial-dir array gives this information so there is no need to have the
num-serializer property in DT description.
Just ignore the property in the driver the DTS files can be updated
separately without regression.
Update the documentation at the same time for davinci-mcasp
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Makes interrupts property optional as the interrupts are not currently
used by the driver and adds interrupt-names property to name listed
interrupts. Currently know interrupt names are "tx" and "rx".
- Improve tdm-slots propery description
- Improve op-mode property description
- Add pinctrl-names and pinctrl-0 properties
- Remove #address-cells and #size-cells as they are not needed.
- Bracket named interrupts property tuples for uniformity.
- Add missing "for" to serial-dir prop in DT bindings doc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
An efm32 features 4 16-bit timers with a 10-bit prescaler. This driver
provides clocksource and clock event device using one timer instance
each.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This enables setting a default trigger on an LP55xx channel,
either from platform data or device tree. This mechanism is
identical to the mechanism for GPIO LEDs and references the
common LEDs device tree bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Milo Kim <milo.kim@ti.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This is based on the work of Teddy Reed <teddy@prosauce.org> published
on GitHub:
https://github.com/theopolis/tpm-i2c-atmel.git
34894b988b67e0ae55088d6388e77b0dbf10c07d
That driver was never merged, I have taken it as a starting port,
forward ported, tested and revised the driver:
- Make it broadly textually similar to the Infineon and Nuvoton I2C
driver
- Place everything in a format suitable for mainline inclusion
- Use high level I2C functions i2c_master_send and
i2c_master_recv for data xfer
- Use the timeout system from the core code, by faking out a status
register
- Only I2C transfer the number of bytes in the reply, not a fixed
message size.
- checkpatch cleanups
- Testing on ARM Kirkwood, with this device tree, using a
AT97SC3204T-X1A180
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
Signed-off-by: Teddy Reed <teddy@prosauce.org>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This chip is/was also branded as a Winbond WPCT301.
Originally written by Dan Morav <dmorav@nuvoton.com> and posted to LKML:
https://lkml.org/lkml/2011/9/7/206
The original posting was not merged, I have taken it as a
starting point, forward ported, tested and revised the driver:
- Rework interrupt handling to work properly with level triggered
interrupts. The old version just locked up.
- Synchronize various items with Peter Huewe's Infineon driver:
* Add durations/timeouts sysfs calls
* Remove I2C device auto-detection
* Don't fiddle with chip->release
* Call tpm_dev_vendor_release in the probe error path
* Use MODULE_DEVICE_TABLE for the I2C ids
* Provide OF compatible strings for DT support
* Use SIMPLE_DEV_PM_OPS
* Use module_i2c_driver
- checkpatch cleanups
- Testing on ARM Kirkwood with GPIO interrupts, with this device tree:
tpm@57 {
compatible = "nuvoton,npct501";
reg = <0x57>;
interrupt-parent = <&gpio1>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Dan Morav <dmorav@nuvoton.com>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes, fixed module name in kconfig]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Change the model omap2-mcasp-audio in compatible property to
am33xx-mcasp-audio as omap2 does not have mcasp.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a separate register location for data port registers to
mcasp DT bindings. On am33xx SoCs the McASP registers are mapped
trough L4 interconnect, but data port registers are also mapped trough
L3 bus to a different memory location.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DLL(Delay Line) is newly added to assist in sampling read data.
The DLL provides the ability to programmatically select a quantized
delay (in fractions of the clock period) regardless of on-chip variations
such as process, voltage and temperature (PVT).
This patch adds a user interface to set slave delay line via device tree.
It's usually used in high speed mode like mmc DDR mode when the signal
quality is not good caused by board design, e.g. the signal path is too
long. User can manually set delay line to find a suitable data sampling
window for card to work properly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The i.MX6 has two general-purpose LVDS clocks that can be driven
from a variety of sources. This patch adds a mux and a gate for
both of these clocks.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There's a pll4_audio_div clock, an extra divider for pll4, missing
in current clock tree, thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
