The Keystone II devices have a set of registers that are used to control
the status of its peripherals. This node is intended to allow access to
this functionality.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller). These are:
* The battery (sbs-battery).
* The power management unit tps65090.
On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).
The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
were caused by the EC, the AP, or some device on the bus).
On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
longer on the bus used for AP/EC communication. The battery was
exposed to the AP through a limited i2c tunnel and tps65090 was
exposed to the AP through a custom Linux driver.
On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.
The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.
This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a driver for the Renesas usdhi6rol0 SD/SDIO host controller
in both PIO and DMA modes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <chris@printf.net>
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
Pull ARM SoC board support updates from Olof Johansson:
"The bulk of this branch is updates for Renesas Shmobile. They are
still doing some enablement for classic boards first, and then come up
with DT bindings when they've had a chance to learn more about the
hardware. Not necessarily a bad way to go about it, and they're
looking at moving some of the temporary board code resulting from it
to drivers/staging instead to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of
in the cleanup branch due to the other board changes depending on it"
* tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (130 commits)
ARM: davinci: remove checks for CONFIG_USB_MUSB_PERIPHERAL
ARM: add drivers for Colibri T30 to multi_v7_defconfig
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
ARM: configs: enable XHCI mvebu support in multi_v7_defconfig
ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP
ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01
ARM: OMAP: SX1: remove check for CONFIG_SX1_OLD_FLASH
ARM: OMAP: remove some dead code
ARM: OMAP: omap3stalker: remove two Kconfig macros
ARM: tegra: tegra_defconfig updates
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
...
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
Pull HSI (High Speed Syncronous Interface) changes from Sebastian Reichel:
"Please pull the following changes for the HSI subsystem, which I have
taken over from Carlos Chinea <carlos.chinea@nokia.com>.
The below patches have been worked on in the linux-omap mailinglist
for 10 months and are well tested in linux-next (have been in there
for more than two weeks) without any problems arising. Apart from
that potential regressions are very limited, because the subsystem is
not yet used by any platform in the mainline kernel.
- Add some documentation for the HSI subsystem
- Add Device Tree support for the HSI subsystem
- Add OMAP3 SSI driver (SSI is a legacy variant of HSI)
- Add Nokia N900 Modem driver (without speech support for now)"
* tag 'hsi-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: Introduce Nokia N900 modem driver
HSI: Introduce driver for SSI Protocol
Documentation: DT: omap-ssi binding documentation
HSI: Introduce OMAP SSI driver
HSI: Add common DT binding for HSI client devices
HSI: export method to (un)register clients
HSI: Add channel resource support to HSI clients
HSI: method to unregister clients from an hsi port
HSI: hsi-char: fix driver for multiport scenarios
MAINTAINERS: update HSI entry
Documentation: HSI: Add some general description for the HSI subsystem
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
Exynos drm hdmi driver used to get dummy hdmiphy clock to
control the PMU bit for hdmiphy. This bit needs to be set
before setting any resolution to hdmi hardware. This was
handled using dummy hdmiphy clock which is removed here.
PMU is already defined as system controller for exynos
SoCs. Hdmi driver is modified to control the phy enable bit
inside PMU using regmap interfaces.
Devicetree binding document for hdmi is also updated.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin. This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Merge "Samsung 3rd DT updates for v3.16" from Kukjin Kim:
- add dts files support for new SoCs
: exynos3250 SoC
: exynos5260 SoC and exynos5260-xyref5260 board
: exynos5410 SoC and exynos5410-smdk5410 board
: exynos5800 SoC and exynos5800-peach-pi board
- exynos4210-origen and exynos4412-origen
: enable RTC and WDT nodes
: use key code macros
- exynos5250-arndale
: use key code macros
- exynos5420-arndale-octa
: add secure firmware support
- exynos5440
: update watchdog node name
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung 3rd clock updates for 3.16" from Kukjin Kim:
- add clock for new exynos5410 SoC
* tag 'samsung-clk-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5410: register clocks using common clock framework
Signed-off-by: Olof Johansson <olof@lixom.net>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a generic PCI host controller, such as a
firmware-initialised device with static windows or an emulation by
something such as kvmtool.
The controller itself has no configuration registers and has its address
spaces described entirely by the device-tree (using the bindings from
ePAPR). Both CAM and ECAM are supported for Config Space accesses.
Add corresponding documentation for the DT binding.
[bhelgaas: currently uses the ARM-specific pci_common_init_dev() interface]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge "Samsung exynos-cpuidle updates for v3.16" from Kukjin Kim:
- From Daniel Lezcano:
This patchset relies on the cpm_pm notifier to initiate the
powerdown sequence operations from pm.c instead cpuidle.c.
Thus the cpuidle driver is no longer dependent from arch
specific code as everything is called from the pm.c file.
* tag 'exynos-cpuidle' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (94 commits)
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
ARM: EXYNOS: Fix S5P_WAKEUP_STAT call for cpuidle
ARM: EXYNOS: Move some code inside the idle_finisher for cpuidle
ARM: EXYNOS: Encapsulate register access inside a function for pm
ARM: EXYNOS: Change function name prefix for cpuidle
ARM: EXYNOS: Use cpuidle_register
ARM: EXYNOS: Prevent forward declaration for cpuidle
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung clock updates for 3.16" from Kukjin Kim:
In this time, it is having dependency with arch/arm/ for 3.16,
I pulled them into samsung tree from Tomasz under agreement from Mike.
- Pull for_3.16/exynos5260 from Tomasz Figa:
"This pull request contains patches preparing Samsung Common Clock Framework
helpers to support Exynos5260 by adding support for multiple clock providers
and then adding clock driver for Exynos5260."
- Pull for_3.16/clk_fixes_non_critical from Tomasz Figa:
"This pull requests contains a number of non-critical fixes for Samsung clock
framework and drivers, including:
1) a series of fixes for Exynos5420 to correct clock definitions and make the
driver closer to the documentation,
2) several missing clocks and clock IDs added to Exynos4, Exynos5250 and
Exynos5420 drivers,
3) fix for incorrect initialization of clock table with NULL,
4) compiler warning fix."
- Pull for_3.16/clk_cleanup from Tomasz Figa:
"This pull requests contains minor clean-up related to Samsung clock
support, including:
1) move Kconfig entries of Samsung clock drivers to drivers/clk,
2) compile drivers/clk/samsung conditionally when COMMON_CLK_SAMSUNG is
selected,
3) remove obsolete Kconfig lines after moving s3c24xx to CCF."
- Pull for_3.16/exynos3250 from Tomasz Figa:
"This small pull request contains a patch adding clock driver for Exynos3250,
which depends on previous pull requests in this series."
- add dt bindings for exynos3250 clock
- add exynos5800 specific clocks in current exynos5420 clock
Note that this branch is based on s3c24xx ccf branch
* tag 'samsung-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (59 commits)
clk: exynos5420: Add 5800 specific clocks
dt-bindings: add documentation for Exynos3250 clock controller
ARM: S3C24XX: fix merge conflict
clk: samsung: exynos3250: Add clocks using common clock framework
drivers: clk: use COMMON_CLK_SAMSUNG for Samsung clock support
ARM: S3C24XX: move S3C24XX clock Kconfig options to Samsung clock Kconfig file
ARM: select COMMON_CLK_SAMSUNG for ARCH_EXYNOS and ARCH_S3C64XX
clk: samsung: add new Kconfig for Samsung common clock option
ARM: S3C24XX: Remove omitted Kconfig selects and conditionals
clk: samsung: exynos5420: add more registers to restore list
clk: samsung: exynos5420: add misc clocks
clk: samsung: exynos5420: update clocks for MAU Block
clk: samsung: exynos5420: fix register offset for sclk_bpll
clk: samsung: exynos5420: correct sysmmu-mfc parent clocks
clk: samsung: exynos5420: update clocks for FSYS and FSYS2 blocks
clk: samsung: exynos5420: update clocks for WCORE block
clk: samsung: exynos5420: update clocks for PERIS and GEN blocks
clk: samsung: exynos5420: update clocks for PERIC block
clk: samsung: exynos5420: update clocks for DISP1 block
clk: samsung: exynos5420: update clocks for G2D and G3D blocks
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Exynos MCPM support for v3.16" from Kukjin Kim:
- adding MCPM backend support for SMP secondary boot and core switching
on Samsung's Exynos5420.
Tested on exynos5420-smdk5420 and exynos5420 based chromebook (peach-pit)
using the "/dev/b.L_switcher" user interface. Secondary core boot-up has
also been tested on both the boards.
* tag 'exynos-mcpm' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add MCPM call-back functions
ARM: dts: add CCI node for exynos5420
ARM: EXYNOS: Add generic cluster power control functions
ARM: EXYNOS: use generic exynos cpu power control functions
ARM: EXYNOS: Add generic cpu power control functions for exynos SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung 2nd DT updates for v3.16" from Kukjin Kim:
exynos4
- add hsotg device, exynos_usbphy nodes
- add PMU syscon and audio subsystem nodes
- replace number by macro in clock binding
exynos4210-universal_c210
- add external sd card node and multimedia nodes
- enable USB functionality
exynos4412-trats2
- enable usb nodes and usb gagdet functionality
- add cm36651 light/proximity sensor node
- fixed gpio key node
exynos5250 and exynos5420
- add pmu syscon handle and sysreg system controller nodes
- add support for usb2phy
- replace number by macro in clock binding
- add USB 2.0 support on exynos5420
exynos5420-peach-pit
- move dp hpd gpio pin to pinctrl_0
* tag 'samsung-dt-2' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (21 commits)
ARM: dts: enable usb nodes for exynos4412-trats2
ARM: dts: add hsotg device node for exynos4
ARM: dts: add exynos_usbphy node for exynos4
ARM: dts: add PMU syscon node for exynos4
ARM: dts: add pmu syscon handle to exynos5420 hdmi
ARM: dts: add pmu syscon handle to exynos5250 hdmi
ARM: dts: replace number by macro in clock binding for exynos5420
ARM: dts: replace number by macro in clock binding for exynos5250
ARM: dts: replace number by macro in clock binding for exynos4
ARM: dts: add external sd card node for exynos4210-universal_c210
ARM: dts: add multimedia nodes for exynos4210-universal_c210
ARM: dts: enable USB functionality for exynos4210-universal_c210
ARM: dts: Enable USB gadget functionality for exynos4210-trats
ARM: dts: Add audio subsystem nodes to exynos4.dtsi
ARM: dts: fixed gpio key node for exynos4412-trats2
ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2
ARM: dts: Add USB 2.0 support on exynos5420
ARM: dts: Add usb2phy support on exynos5420
ARM: dts: Add usb2phy to exynos5250
ARM: dts: Add sysreg sytem controller node to exynos5250 and exynos5420
...
A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The generic SPMI example was missing an equal sign in the assignment
of the #size-cells property.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit extends the compatible string list of the xhci-platform
binding with the new "renesas,xhci-r8a7790" and "renesas,xhci-r8a7791"
compatible strings. It is used to describe the xHCI controller which
is available in the R-Car H2 and M2 SoCs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
