Enable DMA support on i.mx6. The read speed can increase from 600KB/s
to 1.2MB/s on i.mx6q. You can disable or enable dma function in dts.
If not set "dma-names" in dts, spi will use PIO mode. This patch only
validate on i.mx6, not i.mx5, but encourage ones to apply this patch
on i.mx5 since they share the same IP.
Note:
Sometime, there is a weid data in rxfifo after one full tx/rx
transfer finish by DMA on i.mx6dl, so we disable dma functhion on
i.mx6dl.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds basic support for the Broadcom BCM63138 DSL SoC which is
using a dual-core Cortex A9 system. Add the very minimum required code
boot Linux on this SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to support the "enable GPIO" available in many panel devices,
this commit adds a proper devicetree binding.
By providing an enable GPIO in the devicetree, the driver can now turn
off and on the panel device, and/or the backlight device. Both the
backlight and the GPIO are optional properties.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current backlight support is broken; the driver expects a backlight-class
in the panel devicetree node. Fix this by implementing it properly, getting
an optional backlight from a phandle.
This shouldn't cause any backward-compatibility DT issue because the current
implementation doesn't work and is not even documented.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silergy SYR82x regulators share the exact same functionality and register layout
as the Fairchild FAN53555 regulators. Therefore extend the driver to add
support for them.
Both types use the same vendor id in their ID1 register, so it's not possible
to distinguish them automatically.
Similarly, the types also do not match. Type 8 used by the SYR827 and SYR828
start at 712.5mV and increment in 12.5mv steps, while the FAN53555 type 8
starts at 600mV and increments in 10mV steps.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the regulator and add a fairchild vendor-prefix.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCIe controller on Tegra124 has two root ports that can be used in a
x4/x1 or x2/x1 configuration and can run at PCIe 2.0 link speeds (up to
5 GT/s). The PHY programming has been moved into a separate controller, so
the driver now needs to request an external PHY referenced using the device
tree.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Keystone PCI hardware supports both RC and EP modes and devcfg register has
bits to boot strap the device to either of these modes. It seems proper to
add this functionality to the boot loader rather than in the driver as
device will be operating in either mode, not both any time. Currently the
driver supports only RC mode and hence register configuration in the driver
is not needed and the driver can assume the hardware is in RC mode.
Also update the DT documentation accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
On Keystone SOCs, ARM host can send interrupts to DSP cores using the
DSP GPIO controller IP. Each DSP GPIO controller provides 28 IRQ signals for
each DSP core. This is one of the component used by the IPC mechanism used
on Keystone SOCs.
Keystone 2 DSP GPIO controller has specific features:
- each GPIO can be configured only as output pin;
- setting GPIO value to 1 causes IRQ generation on target DSP core;
- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
pending.
This patch updates gpio-syscon driver to be reused by Keystone 2 SoCs,
because the Keystone 2 DSP GPIO controller is controlled through Syscon
devices and, as requested by Linus Walleij, such kind of GPIO controllers
should be integrated with drivers/gpio/gpio-syscon.c driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keystone PCIe controller has a limitation that memory read request size
must not exceed 256 bytes. This is a hardware limitation. Add a quirk to
force this limit on all downstream devices by updating MRRS.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
MMU-401 is similar to MMU-400, but updated with limited ARMv8 support.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds ability to configure delay between transmission of
words over SPI bus if it's required by SPI slave devices.
New optional SPI slave property:
- ti,spi-word-delay : delay between transmission of words
(SPIFMTn.WDELAY, SPIDAT1.WDEL)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LTC2952 is an external power control chip, which signals
the OS to shut down. This patch documents the DT binding
for the chip.
Signed-off-by: René Moll <rene.moll@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull input updates from Dmitry Torokhov:
"A few quirks for i8042/AT keyboards and a small device tree doc fix
for Atmel Touchscreens"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix merge in DT documentation
Input: i8042 - also set the firmware id for MUXed ports
Input: i8042 - add nomux quirk for Avatar AVIU-145A6
Input: i8042 - add Fujitsu U574 to no_timeout dmi table
Input: atkbd - do not try 'deactivate' keyboard on any LG laptops
Aside of the usual boring core properties (compatible, reg, interrupts
and clocks), the bindings use the OF graph bindings to model connections
between the DU output video ports and the on-board and off-board
components.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The THC63LVDM83D is a video LVDS serializer described by an input port,
an output port, and an optional power down GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The ADV7123 is a video DAC described by an input port, an output port,
and an optional power save GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
This fixes a merge conflict in lustre, and we want the other fixes that
went into 3.17-rc5 as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch update fec devicetree binding doc that add Optional
properties "fsl,num-tx-queues" and "fsl,num-rx-queues".
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference to RK3288 TRM, fix an error channel id for i2s tx and rx
Table 10-1 DMAC_BUS Request Mapping Table
Req number Source Polarity
0 I2S tx High level
1 I2S rx High level
Tested on RK3288 board.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
QCOM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
(SNPS) and HS, SS PHY's control and configuration registers.
It could operate in device mode (SS, HS, FS) and host
mode (SS, HS, FS, LS).
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 3.17-rc5.
Nothing major here, just a number of tiny fixes for reported issues,
and some new device ids as well.
All have been tested in linux-next"
* tag 'usb-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (46 commits)
xhci: fix oops when xhci resumes from hibernate with hw lpm capable devices
usb: xhci: Fix OOPS in xhci error handling code
xhci: Fix null pointer dereference if xhci initialization fails
storage: Add single-LUN quirk for Jaz USB Adapter
uas: Add missing le16_to_cpu calls to asm1051 / asm1053 usb-id check
usb: chipidea: msm: Initialize PHY on reset event
usb: chipidea: msm: Use USB PHY API to control PHY state
usb: hub: take hub->hdev reference when processing from eventlist
uas: Disable uas on ASM1051 devices
usb: dwc2/gadget: avoid disabling ep0
usb: dwc2/gadget: delay enabling irq once hardware is configured properly
usb: dwc2/gadget: do not call disconnect method in pullup
usb: dwc2/gadget: break infinite loop in endpoint disable code
usb: dwc2/gadget: fix phy initialization sequence
usb: dwc2/gadget: fix phy disable sequence
uwb: init beacon cache entry before registering uwb device
USB: ftdi_sio: Add support for GE Healthcare Nemo Tracker device
USB: document the 'u' flag for usb-storage quirks parameter
usb: host: xhci: fix compliance mode workaround
usb: dwc3: fix TRB completion when multiple TRBs are started
...
Pull fbdev fixes from Tomi Valkeinen:
"Minor fixes for amba-clcd and video DT bindings"
* tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: ARM CLCD: Fix color model capabilities for DT platforms
video: fix composite video connector compatible string
ARM based platforms implement a variety of power management schemes that
allow processors to enter idle states at run-time.
The parameters defining these idle states vary on a per-platform basis forcing
the OS to hardcode the state parameters in platform specific static tables
whose size grows as the number of platforms supported in the kernel increases
and hampers device drivers standardization.
Therefore, this patch aims at standardizing idle state device tree bindings
for ARM platforms. Bindings define idle state parameters inclusive of entry
methods and state latencies, to allow operating systems to retrieve the
configuration entries from the device tree and initialize the related power
management drivers, paving the way for common code in the kernel to deal with
idle states and removing the need for static data in current and previous
kernel versions.
ARM64 platforms require the DT to define an entry-method property
for idle states.
On system implementing PSCI as an enable-method to enter low-power
states the PSCI CPU suspend method requires the power_state parameter to
be passed to the PSCI CPU suspend function.
This parameter is specific to a power state and platform specific,
therefore must be provided by firmware to the OS in order to enable
proper call sequence.
Thus, this patch also adds a property in the PSCI bindings that
describes how the PSCI CPU suspend power_state parameter should be
defined in DT in all device nodes that rely on PSCI CPU suspend method usage.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sebastian Capella <sebcape@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Many palmas family of PMICs have support for interrupt based power button.
This allows the device to notify the processor of external push button
events over the shared palmas interrupt. However, this event is generated
only during a "press" operation. Software is supposed to poll(sigh!) for
detecting a release event.
The PMIC also supports ability to power off independent of the software
decisions when the button is pressed for a long duration if the PMIC is
appropriately configured on the platform.
Even though the function is similar to twl4030_pwrbutton, it is
substantially different in operation to belong to a new driver of it's own.
Based on original work done by Girish S Ghongdemath <girishsg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull dmaengine fixes from Vinod Koul:
"Two minor fixes.
First one from Kuninori clarifying dmas bindings and second from Lars
for fixing dma descriptor completion in non cyclic case"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: jz4740: Fix non-cyclic descriptor completion
dt/bindings: rcar-audmapp: tidyup dmas explanation
using LVDS channel 1 on an i.MX53 leads to following error:
imx-ldb 53fa8008.ldb: unable to set di0 parent clock to ldb_di1
This comes from imx_ldb_set_clock with mux = 0. Mux parameter must be "1" for
reparenting di1 clock to ldb_di1. The value of the mux param comes from device
tree port settings.
On i.MX5, the internal two-input-multiplexer is used. Due to hardware limitations,
only one port (port@[0,1]) can be used for each channel (lvds-channel@[0,1],
respectively)
Documentation update suggested by Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Fixes: e05c8c9a79 ("ARM: dts: imx53: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
