The esai_ahb clock is derived from ahb and used to provide ESAI the
capability of register accessing and FSYS clock source for I2S clocks
dividing. The gate bits of this esai_ahb clock are shared with the
esai clock -- the baud clock, so we need to call imx_clk_gate2_shared()
for these two clocks.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The mpu_clk, main_clk, and dbg_base_clk outputs from the main PLL go through a
pre-divider. Update socfpga.dtsi to represent those dividers for these
clocks.
Re-use the "div-reg" property that was used for the socfpga-gate-clock as this
is the same thing. Also update the documentation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The APQ8064 and MSM8960 share a significant amount of clock data and
code between the two SoCs. Rather than duplicating the data we just add
support for a unqiue APQ8064 clock table into the MSM8960 code.
For now add just enough clocks to get a basic serial port going on an
APQ8064 device.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: trivial conflict due to missing ipq8064 support]
Document the device tree binding for Broadcom BCM28164 clock control
units and clocks. This SoC uses Kona CCUs, similar to the BCM281XX
SoC family.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The next patch defines a binding for a new Broadcom SoC that uses
Kona style CCUs for its clocks. Update the generic Kona clock
binding document so it's more natural to accomodate the definitions
of additional SoC families.
Specifically:
- Define the compatible string values generically, referring
to specific per-model values later in the document.
- Put the device tree example immediately after the required
properties listing, before the tables of SoC-specific values.
- Clearly identify the start of the section defining specific
values related to the BCM281XX family
- Add a list of the specific BCM281XX family compatible strings.
- Reword the description of the table slightly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Starting with the s3c2443 the s3c24xx series got a new clock tree
compared to the previous s3c24xx socs. This binding describes the
clock controller found in the s3c2443, s3c2416 and s3c2450 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Merge "arm: Xilinx Zynq cleanup patches for v3.15" from Michal Simek:
- Redesign SLCR initialization to enable
driver developing which targets SLCR space
* tag 'zynq-cleanup-for-3.15-v2' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: Add waituart implementation
ARM: zynq: Move of_clk_init from clock driver
ARM: zynq: Introduce zynq_slcr_unlock()
ARM: zynq: Add and use zynq_slcr_read/write() helper functions
ARM: zynq: Make zynq_slcr_base static
ARM: zynq: Map I/O memory on clkc init
ARM: zynq: Hang iomapped slcr address on device_node
ARM: zynq: Split slcr in two parts
ARM: zynq: Move clock_init from slcr to common
arm: dt: zynq: Add fclk-enable property to clkc node
[Arnd: remove SOC_BUS support from pull request]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner sunXi SoCs clock changes
This adds support for the new, more correct clock node naming and gets
the A10 compatibles in line with the rest of the other SoCs. It also
adds support for the USB, GMAC and A31's PLL6 clocks. Some of these
changes also require DT modifications that will be merged via arm-soc.
MOXA ART SoCs allow to determine PLL output and APB frequencies
by reading registers holding multiplier and divisor information.
Add a clock driver for this SoC.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for the new v2 version of the axi-clkgen core.
Unfortunately the method of accessing the registers is quite different on v2,
while the content still stays largely the same. So the patch adds a small
abstraction layer which implements the specific read and write functions for v1
and v2 in callback functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Suggest by Arnd: abstract mmc tuning as clock behavior,
also because different soc have different tuning method and registers.
hi3620_mmc_clks is added to handle mmc clock specifically on hi3620.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The DT bindings document a renesas,indices property, while the code, the
DT example and the DT sources all use renesas,clock-indices. Fix the
documentation.
The shmobile mstp DT bindings have been merged in v3.14-rc1 with a bug
in the DT ABI, a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
clock: mvebu new SoC changes for v3.15
- mvebu (Armada 375/380/385)
- extend corediv clock driver to support new SoCs
- add core and gating clock drivers for new SoCs
Add a property called clock-indices to allow clock-output-names
to be used where the index used to lookup a clock is not a 1:1
mapping to the array position in the clock-output-names
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clk-phase property is used to represent the 2 clock phase values that is
needed for the SD/MMC driver. Add a prepare function to the clk_ops, that will
use the syscon driver to set sdmmc_clk's phase shift that is located in the
system manager.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
---
v9: none
v8: Use degrees in the clk-phase binding property
v7: Add dts property to represent the clk phase of the sdmmc_clk. Add a
prepare function to the gate clk that will toggle clock phase setting.
Remove the "altr,socfpga-sdmmc-sdr-clk" clock type.
v6: Add a new clock type "altr,socfpga-sdmmc-sdr-clk" that will be used to
set the phase shift settings.
v5: Use the "snps,dw-mshc" binding
v4: Use the sdmmc_clk prepare function to set the phase shift settings
v3: Not use the syscon driver because as of 3.13-rc1, the syscon driver is
loaded after the clock driver.
v2: Use the syscon driver
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the clock driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A20/A31 clock module controls the transmit clock source
and interface type of the GMAC ethernet controller. Model this as
a single clock for GMAC drivers to use.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
This atomic commit changes the Integrator clock implementation
and the machines to register clocks from the device tree and
use these instead of the previous hard-coded clocks.
In the clock implementation all hard-coded clocks and the
special initialization function call goes away, and is
replaced by two compatible strings for the two clocks
available on the core module.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clkc has its registers in the range of the slcr.
Instead of passing around the slcr base address pointer, let the clkc get the
address from the DT.
This prepares the slcr to be a real driver with multiple memory ranges
(slcr, clocks, pinctrl,...)
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
clock-output-names is now required for most of sunxi clock nodes, to
provide the name of the corresponding clock. Add the new requirements,
exceptions, as well as examples.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
