The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.
In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.
Also add comments to eeprom_9287.c.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is allocating memory during initialization with GFP_ATOMIC
even though GFP_KERNEL is sufficient. This patch fixes it.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Last patch I sent failed to take into account the offset of each phy.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED support is typically handled via system GPIO on these platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following Felix's recent patchset as an example I have replaced memcmp with
compare_ether_addr.
"Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp."
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report all defined sync_cause errors in debugfs
to aid with debugging.
Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hides some repetitive code, and will help if the
column widths ever need to change.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assumption that irq numbers of asic3 gpios start at
IRQ_BOARD_START is certainly wrong - driver may as well
use any other base for its irqs (consider for example
the imaginary case of two ASIC3 chips onboard)
Furthermore, some platforms even don't have IRQ_BOARD_START
defined, so driver will fail to build on them:
-------------------------------------------------------
drivers/mfd/asic3.c: In function 'asic3_gpio_to_irq':
drivers/mfd/asic3.c:530: error: 'IRQ_BOARD_START' undeclared (first use in this function)
drivers/mfd/asic3.c:530: error: (Each undeclared identifier is reported only once
drivers/mfd/asic3.c:530: error: for each function it appears in.)
-------------------------------------------------------
Fix it by using irq_base from driver data.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Forget to unreserve after pinning. This can lead to problems in
soft reset and resume.
v2: rework patch as per Michel's suggestion.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My rv515 card is very flaky with msi enabled. Every so often it loses a rearm
and never comes back, manually banging the rearm brings it back.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will allow to select this driver for newer SoCs. Make sure to
keep dependency on HAVE_CLK to avoid breaking other machines.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
This will allow to select this driver for newer SoCs.
Keep dependency on AT91 because of the use of an header
file located in include/mach directory.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
This will allow to select this driver for newer SoCs.
Keep dependency on AT91 because of the use of an header
file located in include/mach directory.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In current implementation, to support set_suspend_voltage and set_suspend_mode
the regulator code needs the regulator driver to implement both
set_suspend_enable and set_suspend_disable callbacks.
This patch removes this limitation. In the case set_suspend_enable and/or
set_suspend_disable are NULL, the regulator code assumes we don't need to
do any thing to enable/disable regulator when system is suspended and
then will continue to handle set_suspend_mode and set_suspend_voltage.
Currently the regulator core creates suspend state related sysfs entries only
if both set_suspend_enable and set_suspend_disable callbacks are not NULL.
A side-effect of this change is that the regulator core will create suspend
state related sysfs entries unconditionally now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This regression has been introduced in
commit ca9bfa7eed
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can remove the NULL check here. It triggers a Smatch warning because
list_first_entry() never is NULL and people who check for it normally
intend to check for list_empty() instead. In these cases however,
we've already verified that the lists are not empty.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.
kvalo: fix commit log
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
System crash because of NULL pointer reference due to
cleanup_scatter is not implemented for USB.
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 109d244605
"net/mlx4_en: Set max rate-limit for a TC"
introduced 64 bit math operations into mlx4_en_dcbnl_ieee_setmaxrate()
causing the following final link failure on an x86_32 allmodconfig
ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined!
Convert it to use div_u64() instead.
Cc: Amir Vadai <amirv@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
