Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Taking the cpu hotplug semaphore in a normal events workqueue
is unsafe because other tasks can wait for any workqueues with
it hold. This results in a deadlock.
Move the DBS timer into its own work queue which is not
affected by other work queue flushes to avoid this.
Has been acked by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: Do not overwrite makefile as anohter user
kbuild: drivers/video/logo/ - fix ident glitch
kbuild: fix gen_initramfs_list.sh
kbuild modpost - relax driver data name
kbuild: removing .tmp_versions considered harmful
kbuild: fix modpost segfault for 64bit mipsel kernel
Also remove Bob Burroughs' email address, since it's no longer valid.
Acked-by: Eric D Rossman <edrossma@us.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/rtc/rtc-sa1100.c: In function `sa1100_rtc_proc':
drivers/rtc/rtc-sa1100.c:298: warning: unsigned int format, long unsigned int arg (arg 3)
and arrange for sa1100_rtc_open() to pass the devid to free_irq()
rather than NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The resource data in the network device is intended for ISA and other
older busses, but not for PCI. Don't put PCI data there. Don't (ab)use
the network device for keeping the IRQ number.
Retire orinoco_pci_setup_netdev(), and print some minimal information to
the kernel log instead, identifying the network device and the driver
mostly to identify problems at startup. Scripts should rely on sysfs.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use flags in the spinlocks - the PCMCIA resume functions may not
be called under lock. Don't ignore any errors.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report only the first I/O window and IRQ, and also add the driver name.
The second I/O window, Vpp and configuration index are not interesting
to most users. They can be found by PCMCIA debug tools if needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware resources should not be made available to other devices while
the network device is still registered. Also remove the related debug
statements.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running Linux 2.6.17-rc3-mm1 which has this patch included I get this
interesting message:
airo(eth0): WPA unsupported (only firmware versions 5.30.17 and greater
support WPA. Detected 5.30.17)
airo_test_wpa_capable assumes that the softSubVer part of the firmware
version number is coded in BCD. Apparently, that's not true.
I have firmware version 5.30.17 and cap_rid.softSubVer is 0x11==17.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a crash when
iwconfig ethX mode foo
is done before
ifconfig ethX up
or after
ifconfig ethX down
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address the issue of EDAC/BIOS coexistence for the e752x chip-sets.
We have found a problem where the BIOS will start the system with the error
registers (dev0:fun1) hidden and assuming it has exclusive access to them.
The edac driver violates this assumption.
The workaround this patch offers is to honor the hidden-ness as an
indication that it is not safe to use those registers.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a bug fix for mptspi driver, where after a host reset or
resume, we revalidate the negotiation parameters for all devices.
This bug was introduced when the driver was ported to use the spi
transport layer.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
